语用学中故意违反合作原则产生的语言效果

以语用学中的合作原则为理论框架，以相声演员郭德纲的相声语段为语料，解释合作原则及其四条基本准则，分析了违反四条准则后产生的幽默效果，从而帮助读者更好地理解和欣赏幽默艺术。     

复合材料制造过程仿真技术综述

复合材料制造过程仿真技术的有效应用可以在复合材料构件设计之初对其制造过程中可能出现的缺陷,如分层、孔隙、温度不均、变形等问题进行预测,从而为优化构件结构、调整工艺参数或模具型面提供依据。对目前复合材料设计制造领域常用的一些软件进行简要介绍,并针对目前复合材料制造过程温度场分布和固化变形仿真技术中存在的问题进行了阐述与讨论。     

双脉冲发动机点火过程三维数值模拟

以喷射棒式双脉冲发动机燃烧室、级间隔离装置和喷管一体化为研究对象,采用数值仿真技术对Ⅱ脉冲点火过程三维流场特性进行分析研究。计算结果表明,点火初期燃气压力波峰超前于火焰峰到达级间隔离装置,并以压强冲击波形式传播,Ⅱ脉冲燃烧室相对高压区位置不断发生改变;级间孔打开过程对药柱末端压强影响较大,但对Ⅱ脉冲燃烧室压强整体上升过程影响较小;级间孔打开后,燃气经级间孔加速后形成高度欠膨胀射流,并在Ⅰ脉冲燃烧室内形成非对称带状低压区;级间孔分布的非对称性,导致压强及温度在发动机燃烧室中呈现显著的三维分布特性;高温区出现在隔板附近,而在装药前端、装药末端及外围级间孔轴线附近出现低温区。     

基于遥测数据的无人机气动参数辨识方法研究

针对无人机在高空低速飞行时易受风场影响及在数据分析时遥测数据不完备的问题,进行了气动参数辨识方法研究,提出了基于空速管平面矢量三角形的风场估计方法及基于风场信息修正的气动角估计方法。以某型无人机为例,对遥测数据进行了充分分析与信息综合,运用逐步回归方法进行了纵向气动参数辨识,并进行了实验验证。结果表明,模型计算结果与实测数据吻合较好,说明所提方法有效。考虑到辨识模型的数学本质,该方法对其他固定翼无人机同样适用。     

内外分区空间统一精度场建立方法研究

针对内外分区空间内结构和设备安装的数字化测量需求,研究内外参考点之间的关联技术,构建与外测量精度场相统一的内测量精度场。对于内外空间不同的开口数,利用多测点定位法、二测点和水平仪单站位定位法、二测点和水平仪双站位定位法等方法建立内精度场,实现与外精度场的统一。以某型设备为例进行试验表明,利用内外精度场测量同一检测点进行比较,测量的最大不一致误差为0.14 mm,证明构建模式可行、简单、可靠。     

The geomagnetic solar flare effect identified by SIIG as an indicator of a solar flare observed by GOES satellites

This paper studies the efficiency of geomagnetic solar flare effects (gsfe) in X solar flare detection; so during the period 1999–2007 a comparison between solar flare (sf) observed by satellites of the Geostationary Operational Environmental Satellite (GOES) programme and gsfe published by the Service International des Indices Geomagnetiques (SIIG) is made.     

Plastic deformation analysis and forming quality prediction of tube NC bending

Plane strain assumption and exponent hardening law are used to investigate the plastic deformation in tube bending. Some theoretical formulae including stress, curvature radius of neu-tral layer, angle of neutral layer deviation, bending moment, wall thickness variation and cross-section distortion, are developed to explain the phenomena in tube bending and their magnitudes are also determined. During unloading process, the springback angle is deduced using the virtual work principle, and springback radius is also given according to the length of the neutral layer which remains unchanged before and after springback. The theoretical formulae are validated by the experimental results or the validated simulation results in literature, which can be used to quickly predict the forming quality of tube numerical control (NC) bending.     

The effects of the solar magnetic polarity and the solar wind velocity on Bz-component of the interplanetary magnetic field

We have studied the effect of both solar magnetic polarity and the solar wind velocity on the Bz-component of the interplanetary magnetic field, IMFBz, for the minimum activity of the solar cycles 21, 22, 23 and 24. We made a statistical study of IMFBz in the first section which is considered as an extension of Lyatsky et al. (2003). They made a statistical study of IMFBz for two periods of minimum solar activity 22 and 23 related to 1985–1987 and 1995–1997 when the solar magnetic field had opposite polarity. Our results seem to be consistent with the results obtained by Lyatsky et al. (2003). We found that there is a dependence of IMFBz on the IMFBx and the solar magnetic polarity for the minimum periods of the selected four solar cycles. In addition, we found that there is a dependence of IMFBz on the solar wind velocity.     

温差法在航空机轮导轨装配中的应用

该文介绍了将机轮导轨的冷压装改为热压装工艺,从而降低了生产成本,提高了产品装配质量。     

野战环境下大型飞机超低空气动特性分析

针对野战环境下的大型飞机超低空飞行,采用CFD方法对地面存在前向或横向不对称障碍物时地面效应对气动参数的影响进行了数值分析,包括纵向稳定性和侧向摇晃等问题.研究结果表明,野战等非常规飞行条件下,地面不确定障碍物会造成大型飞机稳定性变差,严重时可能出现纵向点头和横侧向摇晃现象,容易导致触地危险.最后,从现代飞行控制理论角度提出了对常规布局大型飞机进行闭环控制的研究思路.